The third-generation D-STAR repeaters ID-RP2010V/ID-RP4010V/ID-RP1200VD come with more features, power and support to communicate with the amateur world. Internet or optional LTE connection, communicate globally.
Versions: |
ID-RP2010V | ID-RP4010V | ID-RP1200VD | |||
Output Power: |
25W | 25W | 10W | |||
Height: |
2U | 2U | 2U | |||
Frequencies: |
144-148 MHz | 440-450 MHz | 1240-1300 MHz | |||
Modes: |
DV/FM | DV/FM | DV/DD/FM |
Built-in Controller
A built-in controller is constructed on the repeater to work with the RF module unit. Also, each repeater can act independently to forward received signals. Link the repeaters with the supplied Ethernet cable for cross-band operation. The repeater RF module in the repeater can work as a single band D-STAR/FM repeater, the ID-RP2C is not required.
DD Mode Operation*1 ID-RP1200VD Only
The ID-RP1200VD is a 1.2 GHz repeater, switchable between DV or DD mode. The DD mode operation functions as a wireless modem via a computer's Ethernet port to provide data communication and Internet access up to 128 kbps. Use the IC-9700's 1.2 GHz DD mode to set it up as a wireless modem.
Mixed Mode Operation
With mixed mode operation, the repeater can receive and transmit both D-STAR DV and analog FM signals. Great for migrating existing analog repeaters to D-STAR while providing analog compatibility.*2
*2 ID-RP2010V, ID-RP4010V, and ID-RP1200VD cannot perform mixed mode operation when controlled by ID-RP2C.
A built-in controller is constructed on the repeater to work with the RF module unit. Also, each repeater can act independently to forward received signals. Link the repeaters with the supplied Ethernet cable for cross-band operation. The repeater RF module in the repeater can work as a single band D-STAR/FM repeater, the ID-RP2C is not required.
The ID-RP1200VD is a 1.2 GHz repeater, switchable between DV or DD mode. The DD mode operation functions as a wireless modem via a computer's Ethernet port to provide data communication and Internet access up to 128 kbps. Use the IC-9700's 1.2 GHz DD mode to set it up as a wireless modem.
Mixed Mode Operation
With mixed mode operation, the repeater can receive and transmit both D-STAR DV and analog FM signals. Great for migrating existing analog repeaters to D-STAR while providing analog compatibility.*2
*2 ID-RP2010V, ID-RP4010V, and ID-RP1200VD cannot perform mixed mode operation when controlled by ID-RP2C.
Connect the optional LTE unit, UX-262 to directly connect to an LTE network and the Internet. An LTE network can be shared with multiple repeater modules on one site. A data SIM card provides network coverage. A static global IP address is required for the Internet SIM. By combining the internal Gateway function and the LTE unit, a deployable temporary D-STAR repeater site can be created for emergency situations.*3
*3 Please check legal requirements before operating the temporary repeater site
RF Direct Sampling and FPGA Platform
The IDRP2010V/RP4010V repeater uses the latest RF direct sampling method. The ID-RP1200VD uses 1.2 GHz IF Down Conversion sampling. This means that when signals are processed in the FPGA, it greatly improves receiver sensitivity.
Other Features
High Duty Cycle Operation
Replace a repeater module in the ID-RP2 series D-STAR repeaters, as the new modules are compatible with the ID-RP2C controller *2
CW ID/Voice ID Transmitter
SD card slot for firmware updates, saving setting data, FM mode and Voice ID audio
Each RF module has a 10 MHz reference signal input
Each RF module has an internal controller that provides CTCSS, DTCS codes, 1750 Hz tone and programmable CW/Voice ID for analog FM mode
Recommended System Requirements
Cent OS 7 (64-bit)
CPU Clock - 2.4 GHz or faster
RAM Memory - At least 1 GB
Hard Drive: minimum 120 GB
Ethernet Ports - 2 required
D-STAR System Overview
